Comtech-ef-data FX Series Administrator Guide Manuale Utente Pagina 92
- Pagina / 151
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Comtech EF Data / Stampede
FX Series Administration Guide - Version 6.1.1 92
Chapter: FX Series ADC Specific Settings
Section: Overview MN-FXSERIESADM6 Rev 5
5.1.1 General Settings
Figure 5-2 FX Series ADC General Settings Screen
FX Series ADC in “config-only” Mode:
This setting is useful if you are in the process of configuring your FX Series ADC while the unit is
networked in-line. In “Configuration-Only” mode the in-line networking card is put into “bypass” mode so
that traffic is simply passed through. When you are satisfied that the FX Series ADC is properly configured
you can disable this setting. The default setting is “Disabled”.
Enable Dynamic Data Suppression:
This is a global switch that applies to all traffic processed by this FX Series ADC. If “Enabled” then a cache
of data and signatures and byte patterns will be maintained and when possible a signature will be sent
instead of a redundant byte pattern. The default value is “Enabled”.
- FX Series 1
- Table of Contents 3
- Table of Figures 8
- Using This Document 10
- Contacting Product Support 11
- Patents and Trademarks 14
- Conventions and References 15
- Release Notes 18
- Management Port 20
- Trunked VLAN Support 20
- 1 Overview - FX Series 22
- Flexibility 24
- Solutions 24
- 1.3 Single-Sided Solution 25
- 1.3.4 QoS with ACM option 26
- 1.3.5 GZIP Compression 26
- • All HTTP Headers 27
- • Application Cookies 27
- 1.3.8 TCP Optimization 28
- 1.4 Two-Sided Solution 29
- 1.4.7 Multicator 31
- 1.5.1 Theory of Operation 32
- 1.5.2 Reporting 32
- 1.5.3 Deployment Options 32
- 1.6.1 Theory of Operation 33
- • Acceleration Statistics 34
- • Throughput Statistics 34
- 1.7.1 Theory of Operation 35
- Comtech EF Data / Stampede 38
- Back Panels 40
- Front Panel 41
- Rear Panel 42
- Summary of Specifications 42
- Rack Mounting 44
- Tabletop Mounting (Standard) 45
- 2.1.1 Unpacking 46
- 2.1.2 User Interfaces 46
- 2.1.3 Documentation 47
- 3.1.1 Cable the Appliance 48
- 3.2.1 Cable the Appliance 49
- 3.3.1 Cable the Appliance 50
- 4 FX Series Network Settings 53
- 4.2.1 Management Interface 55
- 4.2.2 Auxiliary Interface 56
- Each static 56
- 4.3 Host Settings 57
- 4.3.2 Host File Entries 58
- 4.4 In-Path Interface 59
- In-Band Management: 60
- 4.5 LAN Interfaces 61
- In-Path Interface(s): 62
- MAC Address: 62
- 4.6.1 Overview 64
- Dynamic ACM Parameters 65
- Traffic Control Properties 66
- Packet Compression Settings 66
- Redundancy/Fail Over 67
- Add QoS Filters 68
- View Statistics by QOS Queue 71
- Add QoS Queue 71
- Multicator Controller (MC) 73
- Multicator Transmitter (MT) 73
- Multicator Receiver (MR) 73
- 4.7.1 Theory of Operation 74
- 4.7.2 Multicator Settings 75
- 4.8 Redundancy 79
- 4.9 WCCP 83
- Source IP address: 84
- The subnets: 87
- #show running-config 87
- 5.1 Overview 91
- 5.1.1 General Settings 92
- 5.1.3 Traffic Interception 93
- 5.1.4 System Time 94
- 5.1.5 Software Updates 94
- 5.1.6 Administration 94
- 5.1.7 Other 94
- 5.2 Port Definitions 95
- Configuration: 97
- Status: 97
- General Settings 98
- In-Path Interfaces 98
- 6.2.2 System Time 99
- 6.2.3 Traffic Interception 99
- 6.2.4 Administration 100
- 6.2.5 Other 100
- 6.2.6 Configuration Notes 101
- MN-FXSERIESADM6 Rev 5 102
- ADC Auto-discover: 103
- In-band Management: 104
- 7 FX Series Status 105
- Real-Time Statistics 106
- Action Buttons 107
- 7.2 QOS Status Monitor 108
- QOS Status Matrix 109
- Aggregate Totals 110
- 7.2.3 Modem Status: 111
- 7.2.4 Output Data Rate: 111
- Throughput Statistics 113
- Port Statistics: 113
- ACM QoS: 113
- Routes: 113
- Network Status: 114
- HTTP Log Analysis: 114
- Multicator Status: 114
- HTTP Log Format 115
- Real-Time Statistics 116
- Acceleration Statistics 118
- Other Status Reports 119
- Authorization Realms 120
- Web Application Policies 120
- Layer 5 Application Policies 120
- TurboStreaming: 121
- Realm Name: 122
- Origin IP Address Ranges: 122
- Client Type: 123
- In-Path Interface: 123
- Example: 124
- 8.1.6 Authorization realm 125
- 8.1.7 Enable Acceleration 125
- 8.1.8 Caching 125
- 8.1.9 Content Validation 125
- 8.1.10 Image Optimization 126
- Request GZIP content: 127
- Use reduced window scaling: 127
- 8.4.4 Layer 5 Protocols 134
- 8.4.5 ToS handling method 134
- Backup/Restore Configuration 136
- Change Passwords 136
- Manage Licenses 136
- Shutdown/Restart Appliance 136
- 9.1.3 Change Password 138
- 9.2 Packet Capture 140
- Capture Actions 141
- Download Traces 141
- Sample Capture Filters 141
- 9.3 Update Software 142
- • This Guide 144
- Running the upgrade process 145
- 9.5.1 User Interfaces 146
- Install the software 147
- FX Platform Image Update: 147
- 9.6 FX Series Documentation 149
- 10 Appendix 150
- 10.1.3 Show Status 151
Prodotti e manuali riguardandi Apparecchiature Comtech-ef-data FX Series Administrator Guide
Apparecchiature Comtech-ef-data C5 Manuale Utente
(332 pagine)
(332 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale