Comtech-ef-data RRS11 Manuale Utente

Part Number MN-RRS11 Revision 3 IMPORTANT NOTE: The information contained in this document supersedes all previously

RRS11 Solid-State Transfer Switch MN-RRS11 Preface Rev. 3 iv Warranty Policy Comtech EF Data products are warranted against defects in material and

RRS11 Solid-State Transfer Switch MN-RRS11 Preface Rev. 3 v The warranty excludes any responsibility by Comtech EF Data Corporation for incidental o

RRS11 Solid-State Transfer Switch MN-RRS11 Preface Rev. 3 vi Customer Support Contact the Comtech EF Data Customer Support Department for: • Produc

MN-RRS11 1–1 Rev. 3 Chapter 1. INTRODUCTION 1.1 Overview The RRS11 Solid State Transfer Switch offers IF or L-Band redundancy for the DM240XR in a s

RRS11 Solid-State Transfer Switch Introduction MN-RRS11 1–2 Rev. 3 Notes:

MN-RRS11 2–1 Rev. 3 Chapter 2. Installation This section provides unpacking and installation instructions, and a description of external connections,

RRS11 Solid-State Transfer Switch Installation MN-RRS11 2–2 Rev. 3 2.2 Unpacking The RRS11 Solid-State Transfer Switch was carefully packaged to a

RRS11 Solid-State Transfer Switch Installation MN-RRS11 2–3 Rev. 3 2.3 System Connections Figures 2-1 illustrates a typical setup with an RRS11-L

RRS11 Solid-State Transfer Switch Installation MN-RRS11 2–4 Rev. 3 Figure 2-2 Cable Connections between RRS11 and two DM240XR Units Table 2-2 7

MN-RRS11 3–1 Rev. 3 Chapter 3. Operation 3.1 Solid-State Transfer Switch Operation A functional block diagram of the RRS11/RRS11-L signal flow is il

RRS11 Solid-State Transfer Switch Operation MN-RRS11 3–2 Rev. 3 Figure 3-1 RRS11 Functional Block Diagram

RRS11 Solid-State Transfer Switch Operation MN-RRS11 3–3 Rev. 3 3.2 Operating Procedures The Solid-State Transfer Switch is designed for minimal op

RRS11 Solid-State Transfer Switch Operation MN-RRS11 3–4 Rev. 3 Table 3-1A, RRS11-L L-Band Rear Panel Connectors Connector ID Nomenclature Descript

RRS11 Solid-State Transfer Switch Operation MN-RRS11 3–5 Rev. 3 An additional 9-Pin D-Sub Connector is supplied for switch monitoring. The I/O on t

RRS11 Solid-State Transfer Switch Operation MN-RRS11 3–6 Rev. 3 Notes:

MN-RRS11 4–1 Rev. 3 Chapter 4. Maintenance and Troubleshooting 4.1 Basic Troubleshooting and Maintenance This section provides information on the ba

RRS11 Solid-State Transfer Switch Maintenance and Troubleshooting MN-RRS11 4–2 Rev. 3 Notes:

MN-RRS11 5–1 Rev. 3 Chapter 5. Technical Specifications 5.1 RRS11 and RRS11 L Technical Specifications 5.2 Introduction - RRS11 L-Band Switch This

RRS11 Solid-State Transfer Switch Technical Specifications MN-RRS11 5–2 Rev. 3 5.2.2 Power and Environmental Prime Power: +12 VDC provided to the

METRIC CONVERSIONS Units of Length Unit Centimeter Inch Foot Yard Mile Meter Kilometer Millimeter 1 centimeter — 0.3937 0.03281 0.0109

Copyright © 2010 Comtech EF Data. All rights reserved. Printed in the USA. Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA, 480.333.22

2114 WEST 7TH STREET TEMPE ARIZONA 85281 USA 480 • 333 • 2200 PHONE 480 • 333 • 2161 FAX

This page is intentionally blank.

iii Table of Contents TABLE OF CONTENTS ...

Table of Contents MN-RRS11 RRS11 Solid-State Transfer Switch Rev. 3 iv Notes:

i PREFACE About this Manual This manual describes the installation and operation for the Radyne RRS11. This is a technical document intended for ear

RRS11 Solid-State Transfer Switch MN-RRS11 Preface Rev. 3 ii Cautions and Warnings Trademarks Product names mentioned in this man

RRS11 Solid-State Transfer Switch MN-RRS11 Preface Rev. 3 iii Safety Compliance EN 60950 Applicable testing is routinely performed as a condition of