Comtech EF Data SDM-309B Specifiche Pagina 103
- Pagina / 240
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
M&C and Interfaces SDM-309B Satellite Modem
4-4–26 MN/U-SDM309B Rev. #
indicated by interrogating the modem and by a green Light Emitting Diode (LED) on the
Interface, and is fed into the receive fault tree per IESS-308. Under certain fault
conditions defined by IESS-308 the receive user data will be replaced by an all ones
pattern. A fault will be signaled when this occurs.
4.2.2.5 Plesiochronous Buffer
User data from the Demux Section is fed into a Plesiochronous buffer. The buffer size is
user selectable in bit increments that correspond to the length of an IESS-308 satellite
superframe. These increments turn out to be in 1, 2, 4, 6, 8, 12, 24, and 32 msec. The
buffer is automatically centered on resumption of service after an outage or may be
commanded to center in the interface configuration Section, from the front panel or
remotely. The start up buffer will overfill upon centering to match the satellite frame to
the terrestrial frame with a maximum slide of 0.5 msec. Manual centering will generally
not be Plesiochronous for obvious reasons.
The fill status is available as a monitor function and is accurate to 1%. Overflow or
underflow incidents will be momentarily indicated by red LED’s on the module and are
stored in the ‘stored Fault" Section of the Monitor & Control status registers, along with
the date and time of the incident, provided by the modem internal clock. These are stored
in battery backed RAM.
The user will normally select to have the data clocked out of the buffer by the recovered
clock from the Receive Data Input in order to synchronize the Receive data output with
the satellite data. The user may select from 2 other clock sources as a backup, either a
user supplied "External" reference clock, or the internal" clock source. Problems on
either the Recovered Receive data input clock or the external clock (if selected) will
substitute Satellite clock and a fault will be signaled.
4.2.2.6 Engineering Service Channel (ESC)
The engineering service channel (ESC) uses certain of the satellite overhead bits to
implement an asynchronous RS-232 data channel. This channel works by oversampling
input and output RS-232 data so that no clock signal is required. Data rates up to 1/2000
of the satellite rate may be used.
4.2.2.7 Backward Alarm
A backward alarm is included in the overhead. Basically, backward alarms are sent to the
distant side of an satellite link to signal that there is trouble with the receive side which
may be as a result of improper transmission. The M&C computer monitors the receive
side of the link and in the event of trouble sends an alarm over the transmit side to the
distant end. This alarm signal also indirectly includes faults in the downlink chain since
major problems with the antenna, LNA, or downconverter, etc. will cause an interruption
in service which will fault the modem. Reception of a backward alarm is indicated as one
- SDM-309B 1
- SDM-309BSDM-309B 1
- Warranty Policy 3
- Limitations of Warranty 3
- Exclusive Remedies 3
- Disclaimer 3
- About this Manual 4
- Cautions and Warnings 4
- Metric Conversion 4
- Trademarks 5
- Customer Support 6
- Table of Contents 8
- Rev. 0 vii 10
- Rev. 0 ix 12
- Chapter 1 14
- INTRODUCTION 14
- 1-1–2 MN/U-SDM309B Rev. # 15
- Figure 1-1 SDM-309B Modem 16
- 1-1–4 MN/U-SDM309B Rev. # 17
- MN/U-SDM309B Rev. # 1-1–5 18
- 1-1–6 MN/U-SDM309B Rev. # 19
- 1.4 System Specification 20
- 1-1–10 MN/U-SDM309B Rev. # 23
- MN/U-SDM309B Rev. # 1-1–11 24
- 1-1–12 MN/U-SDM309B Rev. # 25
- Chapter 2 26
- INSTALLATION 26
- Figure 2-1 Rear Panel View 28
- 2.2.1 Data I/O 29
- 2.2.2 Remote (J6) 29
- 2.2.3 Fault (J7) 29
- 2.2.4 IF Output (CP1) 30
- 2.2.5 IF Input (CP2) 30
- 2.2.6 AC Power 30
- 2.2.7 GND 30
- 2.3 System Requirements 30
- 2.4 System Installation 31
- Chapter 3 32
- OPERATION 32
- 3.1.3 Front Panel Controls 33
- Figure 3-1 Front Panel View 34
- 3.1.4 Configuration 35
- 3.1.4.1 MOD Configuration 35
- 3.1.4.2 DEMOD Configuration 36
- 3.1.5 Monitor 41
- 3.1.6 Faults 41
- 3.1.7 Stored Faults 43
- 3.1.8 Utility 43
- Figure 3-2 Menu Tree 47
- Figure 3-3 Menu Tree 48
- Figure 3-4 Menu Tree 49
- Figure 3-5 Menu Tree 50
- Figure 3-6 Menu Tree 51
- Figure 3-7 Menu Tree 52
- Figure 3-8 IF Loopback 53
- Figure 3-9 RF Loopback 54
- 3–24 MN/U-SDM309B Rev. # 55
- MN/U-SDM309B Rev. # 3–25 56
- 3.2.1 General 57
- 3.2.2 Configuration 57
- 3.2.2.1 MOD Configuration 58
- 3.2.2.2 DEMOD Configuration 59
- 3.2.3 Monitor 65
- 3.2.4 Faults 66
- 3.2.5 Stored Faults 67
- 3.2.6 Utility 68
- Figure 3-12 Menu Tree 71
- Figure 3-13 Menu Tree 72
- Figure 3-14 Menu Tree 73
- Figure 3-15 Menu Tree 74
- Figure 3-16 Menu Tree 75
- Figure 3-17 Menu Tree 76
- 3–46 MN/U-SDM309B Rev. # 77
- Chapter 4 78
- M&C AND INTERFACES 78
- Connect JP7 to RS232 79
- MN/U-SDM309B Rev. # 4-4–3 80
- 4.1.2.2 Remote Baud Rate 81
- 4.1.2.3 Remote Address 81
- 4.1.2.4 Battery 81
- 4.1.2.8 Utility Defaults 83
- 4.2 Digital Interfaces 83
- 4.2.1 IBS/M1200P Interface 84
- 4.2.1.2 Data Interface 84
- 4.2.1.3 Transmit Multiplexer 84
- 4-4–8 MN/U-SDM309B Rev. # 85
- MN/U-SDM309B Rev. # 4-4–9 86
- 4-4–10 MN/U-SDM309B Rev. # 87
- Figure 4-4 IBS Fault Tree 88
- Figure 4-5 Jumper Table 89
- 4.2.1.4 Receive Multiplexer 90
- 4-4–18 MN/U-SDM309B Rev. # 95
- 4.2.1.9.7 Send Data (J7) 98
- 4.2.1.9.8 Receive Data (J8) 99
- MN/U-SDM309B Rev. # 4-4–23 100
- 4-4–24 MN/U-SDM309B Rev. # 101
- 4.2.2.2 Data Interface 102
- 4.2.2.3 Transmit Multiplexer 102
- 4.2.2.7 Backward Alarm 103
- MN/U-SDM309B Rev. # 4-4–27 104
- 4-4–28 MN/U-SDM309B Rev. # 105
- MN/U-SDM309B Rev. # 4-4–29 106
- 4-4–30 MN/U-SDM309B Rev. # 107
- MN/U-SDM309B Rev. # 4-4–31 108
- MN/U-SDM309B Rev. # 4-4–35 112
- 4.2.2.10.11 Faults (J11) 115
- 4.2.2.11 Rear Panel Switches 116
- 4.2.2.11.1 Drop Data Input 116
- 4.2.2.11.2 Drop Data Output 116
- 4.2.2.11.3 Insert Data Input 116
- 4-4–40 MN/U-SDM309B Rev. # 117
- MN/U-SDM309B Rev. # 4-4–41 118
- Table 4-3 119
- MN/U-SDM309B Rev. # 4-4–43 120
- 4-4–44 MN/U-SDM309B Rev. # 121
- 4.3.1 Master/Slave 122
- 4.3.1.2 Master/Slave G.703 123
- 4.3.1.3 Master/Slave X.21 123
- 4.3.2 Master/Master 123
- Chapter 5 125
- THEORY OF OPERATION 125
- Figure 5-1 Modulator Card 127
- 5-5–4 MN/U-SDM309B Rev. # 128
- MN/U-SDM309B Rev. # 5-5–5 129
- 5.1.3 Theory of Operation 130
- 5.2.1 General Description 131
- MN/U-SDM309B Rev. # 5-5–9 133
- 5-5–10 MN/U-SDM309B Rev. # 134
- MN/U-SDM309B Rev. # 5-5–11 135
- 5-5–12 MN/U-SDM309B Rev. # 136
- MN/U-SDM309B Rev. # 5-5–13 137
- 5.2.3 Theory Of Operation 138
- 5.2.3.1 Demod Processor 138
- 5.2.3.2 Viterbi Decoder 138
- 5.3 Demodulator 139
- 5.3.1 General Description 139
- 5.3.2 Specifications 140
- Figure 5-9 Demodulator Card 141
- 5-5–18 MN/U-SDM309B Rev. # 142
- 5.3.3 Theory of Operation 143
- 5.4.1 General 143
- 5.4.2 Reacquisition 144
- 5.4.3 Fast Acquisition 145
- 5.4.4 Directed Sweep 145
- Chapter 6 146
- MAINTENANCE 146
- 6-6–2 MN/U-SDM309B Rev. # 147
- MN/U-SDM309B Rev. # 6-6–3 148
- 6-6–4 MN/U-SDM309B Rev. # 149
- Table 6-1 150
- 6-6–6 MN/U-SDM309B Rev. # 151
- MN/U-SDM309B Rev. # 6-6–7 152
- 6.1.4 Test Points 153
- Figure 6-6 154
- Figure 6-7 155
- Figure 6-8 156
- Figure 6-9 157
- 6.2 Fault Isolation 158
- 6.2.1 Modulator Faults 158
- 6.2.2 Demodulator Faults 159
- Table 6-2 162
- 6-6–18 MN/U-SDM309B Rev. # 163
- MN/U-SDM309B Rev. # 6-6–19 164
- 6-6–20 MN/U-SDM309B Rev. # 165
- MN/U-SDM309B Rev. # 6-6–21 166
- 6.4 Module Replacement 167
- 6.5 Module Identification 167
- 6.6 Repacking For Shipment 167
- Table 6-3 168
- Appendix A 169
- DATA RATES AND FILTERS 169
- 1.2 Variable Rate Filters 170
- MN/U-SDM309B Rev. # A–3 171
- A–4 MN/U-SDM309B Rev. # 172
- MN/U-SDM309B Rev. # A–5 173
- A–6 MN/U-SDM309B Rev. # 174
- MN/U-SDM309B Rev. # A–7 175
- A–8 MN/U-SDM309B Rev. # 176
- MN/U-SDM309B Rev. # A–9 177
- Appendix B 178
- SATELLITE MODEM REMOTE 178
- 3.4 End Character 179
- 3.1 Start Character 179
- 3.2 Device Address 179
- 3.3 Command/Responses 179
- 4.2.2 Demodulator Rate 183
- 4.2.4 RF Loop-back (ON/OFF) 184
- 4.2.5 IF Loop-back (ON/OFF) 184
- 4.2.7 Sweep Reacquisition 185
- 4.2.8 Fast Acquisition Mode 185
- 4.2.9 Sweep Center Frequency 185
- 4.2.10 Sweep Width Range 186
- 4.2.11 Sweep Direction 186
- 4.3.12 Interface Buffer Size 188
- 4.3.13 Transmit Data Fault 189
- 4.3.14 Receive Data Fault 189
- 4.3.15 Drop Data Format 189
- 4.3.16 Insert Data Format 189
- 4.4.1 Time Of Day 191
- 4.4.2 Date 191
- 5.3 Modulator Status 195
- 5.4 Demodulator Status 195
- 5.5 Common Equipment Status 196
- 5.8 Bit Error Rate Status 197
- 5.8.1 Raw BER 197
- 5.8.2 Corrected BER 197
- 5.8.3 Corrected BER Log 197
- 5.9 Eb/N0 Status 198
- 5.10 Modulator Rate Status 198
- 5.11 Demodulator Rate Status 198
- 5.13 Current Sweep Value 199
- 5.16 Stored Faults 199
- MN/U-SDM309B Rev. # B-B–23 200
- B-B–28 MN/U-SDM309B Rev. # 205
- 5.20 Change Status 206
- 5.21 Equipment Type 206
- B-B–30 MN/U-SDM309B Rev. # 207
- Appendix C 208
- EXTERNAL CHANNEL UNIT 208
- C-C–2 MN/U-SDM309B Rev. # 209
- MN/U-SDM309B Rev. # C-C–3 210
- C-C–4 MN/U-SDM309B Rev. # 211
- MN/U-SDM309B Rev. # C-C–5 212
- C-C–6 MN/U-SDM309B Rev. # 213
- MN/U-SDM309B Rev. # C-C–7 214
- C-C–8 MN/U-SDM309B Rev. # 215
- MN/U-SDM309B Rev. # C-C–9 216
- C-C–10 MN/U-SDM309B Rev. # 217
- 2.0 Digital Interfaces 218
- 2.1.1 Functional Description 218
- C-C–12 MN/U-SDM309B Rev. # 219
- MN/U-SDM309B Rev. # C-C–13 220
- C-C–14 MN/U-SDM309B Rev. # 221
- 2.1.2 Connector Pinouts 223
- 2.1.3 Specification 223
- 2.2 V.35 Interface 224
- 2.2.1 Functional Description 224
- MN/U-SDM309B Rev. # C-C–19 226
- C-C–20 MN/U-SDM309B Rev. # 227
- 2.2.2 Connector Pinouts 228
- 2.2.3 Specification 228
- 3.0 Front Panel Operation 229
- 3.1 Configuration 229
- 3.2 Monitor 232
- 3.3 Faults 232
- 3.4 Stored Faults 233
- 3.5 Utility 233
- Figure C-13 Menu Tree 235
- Figure C-14 Menu Tree 236
- Figure C-15 Menu Tree 237
- MN/U-SDM309B Rev. # C-C–31 238
- Appendix D 239
- SOFTWARE CHANGE 239
- SPECIFICATIONS 239
Prodotti e manuali riguardandi Networking Comtech EF Data SDM-309B
Networking Comtech EF Data DMD-2050E Specifiche
(342 pagine)
(342 pagine)
Networking Comtech EF Data SDM-650B Specifiche
(434 pagine)
(434 pagine)
Networking Comtech EF Data CDM-710G Specifiche
(136 pagine)
(136 pagine)
Networking Comtech EF Data CDM-800 Specifiche
(130 pagine)
(130 pagine)
Networking Comtech EF Data CDM-710L Specifiche
(172 pagine)
(172 pagine)
Networking Comtech EF Data CDM-710L Specifiche
(242 pagine)
(242 pagine)
Networking Comtech EF Data CIM-550 Specifiche
(460 pagine)
(460 pagine)
Networking Comtech EF Data CDD-880 Specifiche
(124 pagine)
(124 pagine)
Networking Comtech EF Data CDM-840 Specifiche
(244 pagine)
(244 pagine)
Networking Comtech EF Data SDM-100A Specifiche
(212 pagine)
(212 pagine)
Networking Comtech EF Data CDM-Qx Specifiche
(258 pagine)
(258 pagine)
Networking Comtech EF Data CDM-Qx Specifiche
(260 pagine)
(260 pagine)
AEG Electrolux S72380-KA manuels
Manuels d'utilisation et guides de l'utilisateur pour Non AEG Electrolux S72380-KA.
Nous fournissons des manuels en pdf 1 AEG Electrolux S72380-KA à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale